Skip to main content

AA Alive Sdn Bhd · SSM 1204108-DEst. 2016Superbrands Malaysia 2025Batu Caves · Kota Kinabalu · Kuching

WhatsApp 010-905 2891

Haematology Analyser Service Contracts: What to Ask For

When the FBC machine stops, samples go out and results wait. What a service contract should cover, the common types of cover, the exclusions to read first and the records you should receive after every visit.

Also called Hematology analyzer service contract, FBC machine maintenance contract, Hematology analyzer repair, CBC machine service

Published:

What your staff do, and what the engineer does

A service contract does not replace the daily care your operators give the analyser. WHO’s laboratory quality handbook makes day-to-day maintenance the operator’s job, and treats service and repair as a separate question: what does it cost, and can the laboratory get it in its own area? The contract covers the work operators cannot do.

Your operators

Daily start-up and background checks, controls, cleaning cycles, the weekly and monthly tasks in the manual, and first-line troubleshooting.

The operator maintenance schedule

The service engineer

Preventive maintenance, replacing worn and failed parts, repairs, calibration after repair, software updates and safety corrections.

What a contract should cover

  • Preventive maintenance visits: how many a year, spaced through the year, following the manufacturer’s checklist.
  • Repairs: call-outs, labour and travel, and which parts are included.
  • Calibration and functional checks after preventive maintenance and after any repair, before the analyser is handed back.
  • Response time: hours to a first response by phone or remote access, and to an engineer on site in your town, with working hours defined.
  • An uptime figure, if one is offered, with how it is measured and what is excluded.
  • A loan analyser during long repairs, or an agreed arrangement to send samples to another laboratory.
  • Software and firmware updates, including the manufacturer’s field safety corrections.
  • Refresher training when new staff join.
  • A written service report after every visit.

Common types of cover

Names vary between suppliers. NHS Supply Chain’s framework for maintaining medical equipment in England is a useful reference: it lists fully comprehensive, planned preventive maintenance, parts and labour, labour only and best-effort cover, among others. Ask any supplier to map its offer onto terms like these.

TypeWhat it coversWhat you still pay forSuits
ComprehensivePreventive visits and repairs, with parts, labour and travelListed exclusions onlyA single analyser the clinic cannot do without
Preventive maintenance onlyScheduled visits with calibration and checksRepairs and parts when something failsReliable analysers with some budget for repairs
Parts and labourRepairs, with parts, labour and travelPreventive visitsLabs that schedule preventive work separately
Labour onlyEngineer time for repair, calibration or testingAll partsOlder analysers, or labs holding their own spares
Per visitNothing until you callEvery call-out, hour and partBackup analysers or very low use
Best effortSupport where parts or response cannot be guaranteedWhatever cannot be sourcedAnalysers past the maker’s support life

Exclusions to read first

  • Damage blamed on reagents, controls or cleaners not approved for the analyser.
  • Power faults where no surge protection or UPS was used.
  • Wear parts the contract lists as consumables, and how often they are replaced free.
  • Accidental damage, spills and moving the analyser without the engineer.
  • Problems in the LIS or clinic software rather than the analyser.
  • Under reagent rental, service that stops if reagent purchases fall below the commitment.

Records you should receive

WHO recommends an equipment inventory that records the maintenance contract and warranty expiry for each instrument, and a label showing when the next maintenance or service is due. NHS Supply Chain’s framework requires a service record within two working days of every visit and access to the service history for the contract term — a reasonable standard to ask for.

  • A service report for every visit: the fault, the work done, parts replaced and the checks run afterwards.
  • The preventive maintenance checklist, signed and dated.
  • Calibration results, with values before and after where a calibration was performed.
  • The software version installed, and any safety correction applied.
  • The next due date, on the report and on a label on the analyser.
  • The full service history, available to you during and at the end of the contract.

Before the warranty ends

  • Ask for the service contract price with the analyser quotation, so it is part of the comparison from day one.
  • Ask for prices for each year of a multi-year contract, and any cap on annual increases.
  • Start the contract the day the warranty ends, so there is no gap in cover.
  • Ask whether service is done by the licensed establishment that supplied the analyser or by a subcontractor, and whether the engineers are trained on your model. The MDA describes GDPMD — the quality system distributors need for their licence — as covering installation, commissioning, service, maintenance and calibration.
  • Agree what happens to samples while the analyser is down, before it is down.

Frequently asked questions

Do I need a service contract for a haematology analyser?
It is a business decision rather than a rule. Compare the contract price with what a week of downtime costs you in outsourced tests and delayed results. A clinic with one analyser and no backup usually benefits most.
What response time should I ask for?
Ask for two figures in writing: the time to a first response by phone or remote access, and the time to an engineer on site in your town. What is realistic depends on where you are, so compare suppliers on the same terms.
Does the warranty include preventive maintenance?
Not always. Some warranties include scheduled visits and some cover only repairs. Ask for the number of preventive visits during the warranty in writing.
Who calibrates the analyser after a repair?
The engineer, following the manufacturer’s procedure, before handing it back. Your staff then run controls and confirm they are in range before reporting patient results.
Can an independent company service my analyser?
It can. Check that its engineers are trained on your model, that it can get genuine parts and software, and whether using it affects your warranty or any reagent-rental terms.
What should a service visit leave behind?
A written report with the fault, work done, parts replaced and checks performed, calibration results where relevant, the software version, and the next due date.

Get a written quotation

Tell us your clinic or lab type, daily workload and location. We match suitable models and send a written quotation that states who handles delivery, installation and training, and what each costs.

010-905 2891 · Mon–Sat, 9:00 am – 6:00 pm